Maintenance and packaging machinery six steps
2022-09-01 10:05:08
Carton packaging machinery is suitable for continuous greening of various cartons. It is commonly used in both type 30 and type 40. The heat source forms are coal or diesel and electric. It is a packaging equipment machinery commonly used in the processing of carton. The main points of maintenance and repair are as follows:
1. Replace the lubricating oil in the worm gear reducer of the carton packaging machine. The lubricating oil can be selected from No. 10, No. 20 or No. 30 engine oil.
2. After the parts are repaired, the whole machine is assembled, and the machine is turned on to observe whether the machine is running normally. Heat the drum properly and put a small amount of carton packaging machinery oil to melt it to cover the inner surface of the cylinder, then cut off all power. If necessary, spray the paint on the exterior of the machine, cover it with plastic paper after drying, and store it in a dry place.
3. If the chain is too loose, you can first adjust it by removing a few sections. If it has been severely stretched, it should be replaced. When using the carton machinery, it should be used according to a certain amount of methods and principles. Maintenance and maintenance should be carried out in a certain way, and different fault problems should be solved in time. When adjusting and replacing the chain, it should be noted that the installation direction of the spring card at the chain joint should be The chain runs in the same direction to avoid impact, runout or even collision.
4. Wash and wash all rolling bearings and add new grease. Calcium-sodium-based grease can be used.
5. Remove all dirt on the friction surface, especially the chain and sprocket to be cleaned and refilled.
The maintenance and maintenance of carton packaging machinery requires certain technicians to carry out maintenance and repair to ensure the quality and performance of the carton machinery in use, and play an important role and value in the production of carton.
6. Check if the stove is leaking smoke. If smoke is found, check the drum smoke ring, stove and chimney, and find that the damage should be repaired and replaced in time. The electric heating type should check whether the electric heating pipe is damaged or not, and if it is damaged, it should be replaced.
1. Replace the lubricating oil in the worm gear reducer of the carton packaging machine. The lubricating oil can be selected from No. 10, No. 20 or No. 30 engine oil.
2. After the parts are repaired, the whole machine is assembled, and the machine is turned on to observe whether the machine is running normally. Heat the drum properly and put a small amount of carton packaging machinery oil to melt it to cover the inner surface of the cylinder, then cut off all power. If necessary, spray the paint on the exterior of the machine, cover it with plastic paper after drying, and store it in a dry place.
3. If the chain is too loose, you can first adjust it by removing a few sections. If it has been severely stretched, it should be replaced. When using the carton machinery, it should be used according to a certain amount of methods and principles. Maintenance and maintenance should be carried out in a certain way, and different fault problems should be solved in time. When adjusting and replacing the chain, it should be noted that the installation direction of the spring card at the chain joint should be The chain runs in the same direction to avoid impact, runout or even collision.
4. Wash and wash all rolling bearings and add new grease. Calcium-sodium-based grease can be used.
5. Remove all dirt on the friction surface, especially the chain and sprocket to be cleaned and refilled.
The maintenance and maintenance of carton packaging machinery requires certain technicians to carry out maintenance and repair to ensure the quality and performance of the carton machinery in use, and play an important role and value in the production of carton.
6. Check if the stove is leaking smoke. If smoke is found, check the drum smoke ring, stove and chimney, and find that the damage should be repaired and replaced in time. The electric heating type should check whether the electric heating pipe is damaged or not, and if it is damaged, it should be replaced.
Pole Line Hardwares
Poleline Hardware or Power line accessories / fitting widely used in connecting, handling and holding various overhead line systems, insulators, wires, and other utilities. It is an important component of the pole line construction. According to the application, it can be divided into Telecommunication pole hardware, Utility pole mounting hardware Transmission and Tower hardware.
Yokelink supply a full line of Poleline Hardware, we offer from the top of the pole to underground.
Pole Line Hardware,Poleline Hardware,Transmission Hardware,Telecommunication Hardware
Ningbo Yokelink Machinery Co.,Limited , https://www.yokelink.com